Max Security Max-G Pro 4 Specifikace Strana 9
- Strana / 33
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2: Description and Specifications
MatchPort b/g Pro Integration Guide 9
MatchPort b/g Pro Pinouts
There are two headers of 1x20, 2-mm pin spacing. The odd row header is designated as P1; pins
are numbered 1 to 39. The even row header is designated as P2; pins are numbered
2 to 40.
PIN #
NAME
Dir
Active level
FUNCTION
P1.1
RESETIN#
I
Low
Reset. Leave floating if not used.
P1.3
RSTTODFLT
I
Low
Reset to Defaults
P1.5
TX1
O
Transmit Data, port 1
P1.7
RTS1
O
Request to Send, port 1
P1.9
RX1
I
Receive Data, port 1
P1.11
CTS1
I
Clear to Send, port 1
P1.13
CP1
IO
IO Configurable Pin 1
P1.15
CP2
IO
IO Configurable Pin 2
P1.17
CP3
IO
IO Configurable Pin 3
P1.19
CP4
IO
IO Configurable Pin 4
P1.21
TX2
O
Transmit Data, port 2
P1.23
RTS2
O
Request to Send, port 2
P1.25
RX2
I
Receive Data input , port 2
P1.27
CTS2
I
Clear to Send input , port 2
P1.29
CP5
IO
IO Configurable Pin 5
P1.31
CP6
IO
IO Configurable Pin 6
P1.33
CP7
IO
IO Configurable Pin 7
P1.35
RSVD
Reserved. Do not connect
P1.37
S3.3V
I
3.3V Power Input
P1.39
GND
I
Ground
PIN #
NAME
Dir
Active level
FUNCTION
P2.2
GND
I
Ground
P2.4
RSVD
Reserved. Do not connect
P2.6
ETX+
O
PHY’s Differential Ethernet Transmit Data +
P2.8
ETX-
O
PHY’s Differential Ethernet Transmit Data -
P2.10
ETCT
Differential Ethernet Transmit Data Center Tap
P2.12
ERCT
Differential Ethernet Receive Data Center Tap
P2.14
ERX+
I
PHY’s Differential Ethernet Receive Data +
P2.16
ERX-
I
PHY’s Differential Ethernet Receive Data -
P2.18
E_LINKLED
O
Low
Ethernet Link LED.
P2.20
E_ACTLED
O
Low
Ethernet Activity LED.
P2.22
W_LINKLED
O
Low
Wireless LAN Link/Activity LED. Active low
P2.24
BOOTP_EN#
IO
Low
Network Boot and Boot Loader Enable.
P2.26
RSVD
Reserved. Do not connect
P2.28
RSVD
Reserved. Do not connect
P2.30
RSVD
Reserved. Do not connect
P2.32
RSVD
Reserved. Do not connect
P2.34
RSVD
Reserved. Do not connect
P2.36
RSVD
Reserved. Do not connect
P2.38
RSVD
Reserved. Do not connect
P2.40
RSVD
Reserved. Do not connect
Power and Ground
The MatchPort b/g Pro requires a regulated 3.3Vdc +/- 5% power input at P1.37 and
ground at pin P1.39.
- MatchPort b/g Pro 1
- Integration Guide 1
- Copyright and Trademark 2
- Contacts 2
- Disclaimer and Revisions 2
- Disclaimer 2
- Revision Table 3
- Contents 4
- List of Figures 5
- List of Tables 5
- 1: Introduction 6
- Power and Ground 9
- Ethernet Connections 10
- Ethernet LED Connections 11
- Wireless LED Connections 11
- Antenna Mating Connector 11
- Antenna 12
- Serial Input/Output 13
- IO Configurable Pins (CPs) 15
- BOOTP_EN# 16
- Electrical Specifications 17
- Wireless Specifications 18
- Technical Specifications 18
- Dimensions 19
- Figure 2-13. Top View 20
- Figure 2-14. Bottom View 20
- Recommended PCB Layout 21
- Product Information Label 22
- 3: Demonstration Kit 23
- Serial Interfaces 24
- Power Supply 24
- General Control 24
- Configuration Switch Bank 25
- Demo Board Layout 27
- Demo Board Schematics 28
- A: Compliance 32
- B: Warranty 33
Související produkty a manuály pro Digitální videorekordéry (DVR) Max Security Max-G Pro 4
(47 stránky)Livarno Z30378 manuels
Manuels d'utilisation et guides de l'utilisateur pour Éclairage Livarno Z30378.
Nous fournissons des manuels en pdf 3 Livarno Z30378 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce